UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit
UH-60 tail rotor pitch beam puller and pitch beam nut socket kit

Sikorsky UH-60 blackhawk tail rotor pitch beam tool kit

CA$4,500.00
1 available

This set of tools contains both our pitch beam puller and pitch beam nut socket; all the tools needed to remove and install the tail rotor pitch beam. Ideal for Phased Maintenance Inspections(PMI) and tasks requiring pitch beam removal.

Tail Rotor Pitch Beam Nut Socket PN: UH60PBNS

Our Sikorsky UH60/S70 Blackhawk pitch beam nut socket eases tail rotor pitch beam nut removal and torquing. Used in place of the spanner adaptor and uses two pin holes for torquing, reducing the chance of hole elongation.

Accepts a 1/2” drive socket wrench.

‘Pitch Beam Puller PN: UH60PBP

Lightweight and compact Sikorsky UH-60 Blackhawk tail rotor pitch beam puller. Our tool is a blank sheet design prioritizing simplicity, ease of use and affordability. It provides 360-degree support of the pitch beam inboard face when removing the pitch beam, unlike other models.

The tool disassembles and packs flat for transport and field maintenance.

Alternate PN’s: 5120-00-948-3923, 65700-10048-041, PBP-60-AA

This set of tools contains both our pitch beam puller and pitch beam nut socket; all the tools needed to remove and install the tail rotor pitch beam. Ideal for Phased Maintenance Inspections(PMI) and tasks requiring pitch beam removal.

Tail Rotor Pitch Beam Nut Socket PN: UH60PBNS

Our Sikorsky UH60/S70 Blackhawk pitch beam nut socket eases tail rotor pitch beam nut removal and torquing. Used in place of the spanner adaptor and uses two pin holes for torquing, reducing the chance of hole elongation.

Accepts a 1/2” drive socket wrench.

‘Pitch Beam Puller PN: UH60PBP

Lightweight and compact Sikorsky UH-60 Blackhawk tail rotor pitch beam puller. Our tool is a blank sheet design prioritizing simplicity, ease of use and affordability. It provides 360-degree support of the pitch beam inboard face when removing the pitch beam, unlike other models.

The tool disassembles and packs flat for transport and field maintenance.

Alternate PN’s: 5120-00-948-3923, 65700-10048-041, PBP-60-AA

Sikorsky UH-60 Blackhawk tail rotor head bolt organizer
Sikorsky UH-60 Blackhawk tail rotor head bolt organizer
CA$100.00

Safety instructions

Improper use of tools and non-observance of these safety notes can lead to personal injury and property damage.

Completely read, understand and observe the safety notes before use.

This tool is intended only for qualified, skilled personnel.

Always use personal protective equipment (for example safety glasses, safety shoes, protective gloves and suitable working clothes) necessary to protect you from exposure to potential hazards.

Employers are responsible for the safe condition of tools and equipment used. They must notify supervisors and replace damaged tools. Do not use socket wrenches when jaws are sprung to the point that slippage occurs. Keep the floor as clean and dry as possible to prevent slips or trips.

Terms of Sale

Every order is subject to our Terms of Sale, in the last section of our About page, which limit our liability, including for our negligence, and contain an indemnity. Please read them before you order.